+48 500 409 109

How do you budget for a sandwich panel garage from the foundations to installation?

A sandwich panel garage can be closed efficiently once the foundation, frame and all openings have been prepared in advance. The price of the panels alone is not the price of the finished structure. The budget must also include the door, flashings, transport and installations. A good plan combines these items with the sequence of works to avoid downtime. Determine the dimensions, height and intended use of the garage. Not only the size of the car matters. Space is needed for opening doors, storing equipment and possibly a workbench. Note whether the structure will be heated. A garage used as a workshop has different needs than a car shelter.

By |2026-11-14T14:19:38+01:002024-10-07|Blog|Comments Off on How do you budget for a sandwich panel garage from the foundations to installation?
Read More

Roof sandwich panels versus single-skin metal sheets

A roof sandwich panel combines two facings with an insulating core into one element, whereas trapezoidal sheet alone is a single layer. Check whether the building will be heated, what loads apply and how the entire roof has been designed — these factors determine the choice. The roof version has a profiled surface and a side lap for water drainage, and its geometry differs from a wall panel. Assess the specific product with defined facing thicknesses, because core thickness alone does not explain all differences. Leave design decisions to the designer.

By |2026-11-14T21:03:05+01:002024-09-28|Blog|Comments Off on Roof sandwich panels versus single-skin metal sheets
Read More

Installing sandwich panels on a steel frame: matching the cladding to its supports

The panels have been selected correctly, but after unpacking it turns out that the supports do not lie in one plane. Tightening the screws harder is not a solution to this problem. Installation of the steel hall cladding begins with checking the frame. Only on the prepared structure can connections be made in accordance with the design and the panel manufacturer's instructions. This ensures that the material works under the conditions for which it was intended. The check covers the position and geometry of the columns, rails or purlins. The width of the surface on which the panel rests is also important. The steel structure should correspond to the cladding drawings and the permitted tolerances. Discrepancies should be clarified before installation, rather than carried over to subsequent rows of panels.

By |2026-11-15T04:43:10+01:002024-08-14|Blog|Comments Off on Installing sandwich panels on a steel frame: matching the cladding to its supports
Read More

How do you choose sandwich panels and budget for cladding before extending a building?

An extension begins with the decision on how the larger building should function. Only then are the panels selected and their cost calculated. The new part should match the structure, internal conditions and construction programme. It is worth following this sequence before the first material quote appears. Determine what will change once the work is complete. Will the new part be heated, how often will the gates open and what processes will take place inside? Extending a warehouse with a workshop may mean different requirements than adding another dry storage space.

By |2026-11-14T14:21:15+01:002024-06-07|Blog|Comments Off on How do you choose sandwich panels and budget for cladding before extending a building?
Read More

How do insulated sandwich wall panels work and what are their advantages?

A sandwich wall panel is a component with two steel facings and a permanently bonded insulating core, allowing walls of a building with suitably prepared structure to be closed efficiently. When choosing, comparing thickness and colour alone is not enough. You should check the thermal performance of the whole panel, fire requirements, permissible span, type of joint, and detailing at the base and openings. Each of these parameters affects the product's suitability for a specific application, so it is worth comparing them side by side for the variants under consideration.

By |2026-11-15T00:56:07+01:002024-04-27|Blog|Comments Off on How do insulated sandwich wall panels work and what are their advantages?
Read More

When does a sandwich panel roof need extra insulation?

A sandwich panel already contains an insulation layer. Additional insulation is therefore not a mandatory stage of every roof. It may be needed after a change of use or when modernising an old building. First, however, the existing layers, airtightness and moisture must be checked. Only then is a solution chosen. A cold interior does not prove that the whole roof has too little insulation. Heat may escape through an open gate, a leaky joint or a poorly executed service penetration. A damp patch also does not clearly indicate the cause. Rainwater, condensation and construction moisture must be distinguished.

By |2026-11-14T14:22:30+01:002024-02-27|Blog|Comments Off on When does a sandwich panel roof need extra insulation?
Read More

Comparing sandwich panel prices per square metre, including surcharges

Two prices per square metre may relate to completely different panels. The core, sheet thickness, coating and method of calculating area make the difference. Lengths, accessories and delivery are also added to the calculation. Before choosing the lower amount, bring the offers to a common scope. Below you will find a simple method for such a comparison. Check whether the price relates to a square metre, a linear metre or the whole element. With a cover width of 1.00 m, the area and length values are numerically the same. This can hide a mistake. For a panel of a different width, the result will already differ.

By |2026-11-14T14:22:37+01:002024-01-30|Blog|Comments Off on Comparing sandwich panel prices per square metre, including surcharges
Read More

What the name Oborniki panel means when buying building panels

Płyta obornicka is the colloquial name for a sandwich panel. In conversation it helps to identify the group of materials, but it is not enough to place an order. Under this term you can find various cores, facings and applications. If you are extending a building, first identify the existing panel. Then select the new material and the method of connecting both parts. A typical sandwich panel for cladding has two thin facings and an insulating core. The facings are often made of coated steel. The core may be PIR or PUR foam, polystyrene or mineral wool. The layers are bonded and work together as a component intended for a specific application.

By |2026-11-14T17:30:04+01:002023-12-27|Blog|Comments Off on What the name Oborniki panel means when buying building panels
Read More

Measuring the pitch of a roof before specifying the covering

First establish whether the stated pitch is given in degrees or as a percentage, and only then compare materials. Check where the manufacturer specifies the minimum slope for the particular profile and roof build-up, not merely for the board name. Measure the height difference and the corresponding horizontal distance, preferably from the current design. Before ordering or accepting delivery, confirm that the chosen covering variant matches the actual roof conditions, including sheet lengths and planned joints.

By |2026-11-15T04:41:16+01:002023-10-24|Blog|Comments Off on Measuring the pitch of a roof before specifying the covering
Read More

Choosing cold-room and freezer panels before the refrigeration equipment goes in

The thickness of a cold room panel depends on temperatures and how the chamber operates. Knowing its surface area is not enough. Doors, opening frequency and the temperature of incoming goods matter. It is worth selecting the enclosure and installation together so that no additional openings are cut in finished partitions after installation. Provide the internal temperature and ambient conditions of the chamber. Determine whether it will be a cold room or a freezer. Record the type and quantity of goods, their incoming temperature and the delivery rhythm. The energy needed to cool the product is a different item from the heat passing through the wall.

By |2026-11-14T14:19:40+01:002023-06-26|Blog|Comments Off on Choosing cold-room and freezer panels before the refrigeration equipment goes in
Read More
Back to top