About PiVi

This author has not yet filled in any details.
So far PiVi has created 1404 blog entries.

Selecting roof panel lengths from the stock actually available

An urgent renovation often starts with the question of what is in stock. A ready-made length can speed up delivery, but it must fit the roof geometry and the method of support. There is no single list of lengths permanently available from every supplier. You need to check the specific batch, calculate the cutting plan and confirm its completeness. Availability information should relate to a specific number of sheets, length and variant. Stock levels can change between the first phone call and placing the order. Ask for confirmation of quantity and collection date. Link the reservation to an exact material schedule.

By |2026-11-14T17:29:14+01:002024-02-03|Blog|Comments Off on Selecting roof panel lengths from the stock actually available

Comparing sandwich panel prices per square metre, including surcharges

Two prices per square metre may relate to completely different panels. The core, sheet thickness, coating and method of calculating area make the difference. Lengths, accessories and delivery are also added to the calculation. Before choosing the lower amount, bring the offers to a common scope. Below you will find a simple method for such a comparison. Check whether the price relates to a square metre, a linear metre or the whole element. With a cover width of 1.00 m, the area and length values are numerically the same. This can hide a mistake. For a panel of a different width, the result will already differ.

By |2026-11-14T14:22:37+01:002024-01-30|Blog|Comments Off on Comparing sandwich panel prices per square metre, including surcharges

Picking a roof covering for halls and industrial sites

First establish how the building will be used, because this defines the function of the entire envelope. Check whether the hall is heated, what the support spacing is and what conditions prevail inside. In an unheated facility a trapezoidal sheet may sometimes suffice, but condensation must be anticipated; in a heated one a full insulation system or a sandwich roof panel is needed. Fire requirements, moisture, acoustics and planned rooftop installations also influence the choice. The designer should link these data to the selection of profile, sheet thickness and support scheme rather than copying a ready-made solution.

By |2026-11-14T21:01:01+01:002024-01-24|Blog|Comments Off on Picking a roof covering for halls and industrial sites

Clearing snow from roofs: when is it needed and how should it be organised?

Whether a roof needs clearing follows from the load, the state of the structure and the weather — not from a single depth measurement. Damp, compacted snow can be far heavier than fresh powder; the same layer varies in mass with its water content and how packed it is. A thaw, rain or refreezing alters conditions on the roof. Uneven deposition counts as well: drifts at parapets and higher parts of the building stress the structure locally more than an even cover. The owner should monitor the building and arrange safe works.

By |2026-11-14T21:00:37+01:002024-01-17|Blog|Comments Off on Clearing snow from roofs: when is it needed and how should it be organised?

Where roof meets wall: cold-formed sections at eaves and corners

Across a roof or wall, many elements repeat at regular intervals. At the eaves and corners, this rhythm changes. Purlins, rails, panels, flashings and drainage elements meet. Cold-formed profiles help to organise this zone, provided each one is given the right function. A good detail should be clear to several trades. Its essential parts must not be left to be fitted after the cladding has been installed. The last purlin is not always the only support needed in the eaves area. The end of the panel, the flashing and the method of water drainage must be taken into account. An eaves profile or an additional substructure element may be required. Its shape should match the actual detail. Not every bent metal sheet should be called a load-bearing element for any application.

By |2026-11-15T20:21:06+01:002024-01-16|Blog|Comments Off on Where roof meets wall: cold-formed sections at eaves and corners

Preparing gutters for winter: checking outlets and joints after cleaning

Vacuuming clears loose leaves and needles from a gutter, but it tells you little about how the water drains. A winter service should cover the outlets, downpipes and joints, right through to the discharge point. Check whether water stands in the gutter after cleaning: a vacuum cannot correct the fall or repair a cracked joint. Wet leaves packed against an outlet may also need a different cleaning method. When arranging the work, agree which parts of the system the contractor will inspect.

By |2026-11-15T04:42:23+01:002024-01-15|Blog|Comments Off on Preparing gutters for winter: checking outlets and joints after cleaning

How to reduce the risk of leaks in a metal roof

The watertightness of a metal roof is decided at the design and material selection stage, not by the amount of sealant alone. Before purchase, check the instructions for the specific profile, as slope requirements differ for tile-effect sheets, trapezoidal sheets and sandwich panels, and may also vary with longitudinal joints. Measure the actual roof, especially during renovation, so deflections do not trap water. Focus most attention on valleys, chimneys, penetrations and unobstructed drainage. Correct runoff and careful details are the basis of watertightness throughout the service life.

By |2026-11-14T21:02:46+01:002024-01-02|Blog|Comments Off on How to reduce the risk of leaks in a metal roof

Square gutters on a metal roof: shape, capacity and detailing

In Poland, a square gutter stands out mainly for its appearance, not automatically for greater capacity. Its shape pairs well with metal roofing and simple flashings, underlining a modern building form. Before choosing, check the actual cross-section, outlet positions, fixing method and access for cleaning. Also consider the system variant — visible, covered by a fascia or concealed — and compare colour on real samples with the roofing and joinery. Leave the sizing decision to the designer, as the whole arrangement up to the pipe outlet matters.

By |2026-11-14T17:32:13+01:002023-12-30|Blog|Comments Off on Square gutters on a metal roof: shape, capacity and detailing

What the name Oborniki panel means when buying building panels

Płyta obornicka is the colloquial name for a sandwich panel. In conversation it helps to identify the group of materials, but it is not enough to place an order. Under this term you can find various cores, facings and applications. If you are extending a building, first identify the existing panel. Then select the new material and the method of connecting both parts. A typical sandwich panel for cladding has two thin facings and an insulating core. The facings are often made of coated steel. The core may be PIR or PUR foam, polystyrene or mineral wool. The layers are bonded and work together as a component intended for a specific application.

By |2026-11-14T17:30:04+01:002023-12-27|Blog|Comments Off on What the name Oborniki panel means when buying building panels

Tile-effect metal roofing or concrete tiles: what suits your roof?

The choice between metal roofing and concrete tiles depends mainly on whether the roof structure and pitch are ready for the heavier covering. Metal roofing is usually much lighter, while concrete tiles consist of many small, individually replaceable elements. Check the load-bearing capacity of the structure, the roof pitch, the manufacturer's requirements for underlayers and fixings, and the full estimate including accessories and flashings. The price per square metre of material alone does not settle the comparison, and the decision should be made before ordering.

By |2026-11-14T21:01:16+01:002023-12-13|Blog|Comments Off on Tile-effect metal roofing or concrete tiles: what suits your roof?
Back to top