About PiVi

This author has not yet filled in any details.
So far PiVi has created 1404 blog entries.

Cleaning moss and green growth from metal roofing tiles safely

Identify the green deposit on the metal roofing tile first, then remove it, because moss, algae and ordinary dirt require different methods. Check the type and adhesion of the soiling and the condition of the coating before choosing a cleaning method. Base the assessment on a trial in a less visible place if documentation for the covering is available. Also check that gutters, valleys and outlets are clear, since accumulated leaves trap moisture and can encourage the deposit to return. Remember that shaded roof areas and places near trees dry more slowly, so green marks may appear unevenly and need not indicate a fault in the sheet.

By |2026-11-14T21:02:50+01:002024-04-08|Blog|Comments Off on Cleaning moss and green growth from metal roofing tiles safely

Storing metal fence pickets delivered before installation

The delivery date does not always coincide with the structure being ready. Metal fence pickets must then wait for installation. This is an important stage, because the finished coating can be damaged before use. Packaging secured for transport is not automatically prepared for long-term storage. It is worth planning the storage location before the vehicle arrives. Check how the elements have been packed and what equipment or how many people are needed to move them safely. Long pickets should not hang unsupported or strike the ground with their ends. The unloading arrangements must match the delivery. A lack of prepared space often leads to the material being put down where it can easily be damaged.

By |2026-11-15T20:21:24+01:002024-03-26|Blog|Comments Off on Storing metal fence pickets delivered before installation

Understanding T18 and T35 markings and trapezoidal sheet specifications

In Poland, the designation T18 or T35 indicates only the profile of a trapezoidal sheet, not its full specification. When buying, you should also read the core thickness, cover width, steel grade and coating, then check the intended use of the sheet and its laying orientation. The name alone does not replace a technical drawing, so it is worth comparing the product documentation and confirming whether two similarly named sheets are technically identical. A full description also makes delivery acceptance and later selection of repair material easier.

By |2026-11-14T17:32:28+01:002024-03-25|Blog|Comments Off on Understanding T18 and T35 markings and trapezoidal sheet specifications

Which roof covering costs least once you include installation?

The lowest price per sheet does not always give the cheapest finished roof. The shape of the roof slopes, the required substrate and the number of details all matter. For a simple roof, trapezoidal steel sheet can be a sensible solution. However, the final cost must be calculated for the same task and a comparable scope of work. First, separate the weatherproof covering alone from the construction of an insulated building envelope. An uninsulated canopy and a roof over a workshop require a different build-up. The price of a single sheet is not comparable with the price of a complete sandwich panel without taking the other layers into account.

By |2026-11-14T14:21:40+01:002024-03-11|Blog|Comments Off on Which roof covering costs least once you include installation?

When does a sandwich panel roof need extra insulation?

A sandwich panel already contains an insulation layer. Additional insulation is therefore not a mandatory stage of every roof. It may be needed after a change of use or when modernising an old building. First, however, the existing layers, airtightness and moisture must be checked. Only then is a solution chosen. A cold interior does not prove that the whole roof has too little insulation. Heat may escape through an open gate, a leaky joint or a poorly executed service penetration. A damp patch also does not clearly indicate the cause. Rainwater, condensation and construction moisture must be distinguished.

By |2026-11-14T14:22:30+01:002024-02-27|Blog|Comments Off on When does a sandwich panel roof need extra insulation?

Replacing one metal picket in an existing fence

A damaged picket does not always require replacing the entire bay. In many fences, the elements are fixed separately, which allows the repair to be focused on one place. However, this does not mean that every similar picket will fit. Profile data, an assessment of the connections and a dismantling plan are needed. A well-prepared replacement reduces the risk of damaging adjacent surfaces. Locate the specification or marking from the original delivery. Check the width, the depth of the section, the run of the grooves and the edge finish. Two metal pickets of similar width may have different bends. Once fitted side by side, the difference can be obvious, even when the colour is similar.

By |2026-11-15T20:21:29+01:002024-02-24|Blog|Comments Off on Replacing one metal picket in an existing fence

How do I order made-to-measure tile-effect metal roofing after measuring the roof truss?

An order for made-to-measure tile-effect metal roofing should follow from measuring the completed structure. You need the rafter lengths, widths and positions of obstacles. Add the profile and coating data. A good schedule combines the roof geometry with the installation plan. This means the material arrives in the order the crew needs it. It is safest once the final truss geometry and the support for the covering have been established. The design is the starting point, but the built structure may have deviations. Check the lengths at both edges of the slope and the diagonals. This reveals differences that will affect the layout of the sheets.

By |2026-11-14T11:10:56+01:002024-02-19|Blog|Comments Off on How do I order made-to-measure tile-effect metal roofing after measuring the roof truss?

Storing corrugated fibre cement sheets: keeping them dry and ventilated

Once installed, a rain-resistant sheet should not have been lying in a wet pack. Corrugated fibre cement sheets require a prepared storage area and protection suited to the delivery. Asbestos-free fibre cement can remain on site until installation, but storage conditions affect the appearance, geometry and ease of subsequent work. On the roof slope, water runs off the surface and the material is in contact with the air. In a tight stack, moisture can remain trapped between the sheets. For this reason, weather resistance does not mean the material can be stored any way you like. The pack must be protected against flooding and against water remaining inside for long periods. It is not enough to check whether rain is falling directly from above.

By |2026-11-15T20:23:06+01:002024-02-17|Blog|Comments Off on Storing corrugated fibre cement sheets: keeping them dry and ventilated

Storing galvanised steel sections before installation

A profile can arrive on site in good condition and still be damaged before it becomes part of the structure. Poorly prepared storage is a common cause. Moisture, uneven support and repeated handling are bad for thin components. Galvanised profiles need protection from water and from deformation. The storage plan does not have to be complicated. It must, however, match the material lengths and the actual sequence of work. The ground should allow packs to be laid down stably and equipment to be accessed safely. Water traps and places exposed to accidental impacts must be ruled out. Distance from the ground is also important. Cold-formed profiles should not lie directly on a wet surface. It is worth planning the bearers and their layout rather than looking for random boards during unloading.

By |2026-11-15T20:19:33+01:002024-02-13|Blog|Comments Off on Storing galvanised steel sections before installation

Choosing insulation for the roof structure

The choice of roof insulation depends mainly on where the boundary of the heated part of the building runs. Check whether the loft will be usable or remain an unheated attic, as this determines the scope of insulation. Pay attention to the continuity of the thermal layer, including the knee walls, stairs and access to the attic. When selecting a material, compare lambda, thickness, reaction to fire, acoustics and installation requirements. PIR boards are worth considering where there is insufficient space for a thicker layer. Make the decision before ordering the material.

By |2026-11-15T00:58:21+01:002024-02-11|Blog|Comments Off on Choosing insulation for the roof structure
Back to top