About PiVi

This author has not yet filled in any details.
So far PiVi has created 1504 blog entries.

When is a rooflight a good way to bring daylight indoors?

A roof light is a good solution when an interior needs daylight in places far from wall windows, for example in wide halls, workshops or corridors. It is worth checking whether light from the roof will reach closer to workstations or the storage area, taking into account the arrangement of racks, partitions and equipment as well as the risk of glare. The roof light's compatibility with the covering, structure and thermal requirements must be confirmed, and it should be established whether it serves only daylighting or also ventilation or smoke exhaust.

By |2026-11-15T00:58:18+01:002022-09-27|Blog|Comments Off on When is a rooflight a good way to bring daylight indoors?

Metal pickets in pedestrian and driveway gates: checks during use

Metal fence pickets on a fixed bay and on a gate leaf may look similar. However, the conditions of use are not the same. The gate and driveway gate open, close and interact with the hardware. It is worth checking them as a complete system. A nice coating on the infill does not yet tell you whether the leaf operates correctly and does not interfere with the pickets during everyday movement. Check the closed and open positions in accordance with the intended use of the device. Pay attention to the points where it approaches the posts, the ground and adjacent elements. A picket should not rub accidentally during movement. A mark visible only at one end may indicate a problem with the alignment of the whole leaf. During the inspection, compare the street side and the garden side. An element that looks correct at the front may have a mark of contact with a crossbar or hardware at the back.

By |2026-11-15T20:21:56+01:002022-09-18|Blog|Comments Off on Metal pickets in pedestrian and driveway gates: checks during use

How do you calculate the weight of mineral wool panels for delivery and installation?

The weight of a mineral wool panel depends on the core thickness, its type and the steel facings. For delivery planning, the total weight of the batch is needed. For installation, the weight and length of the individual element also matter. These two aspects should not be confused. Even a relatively light pack may contain panels that are difficult to handle. It is best to use data for the precisely selected variant. Panels of the same thickness may have a different core and facings. An example wall panel 100 mm with mineral wool of nominal density 100 kg/m³ and 0.5/0.5 mm steel sheets weighs approximately 18.1 kg/m². A lighter variant of this thickness may weigh 16.6 kg/m².

By |2026-11-14T11:11:41+01:002022-09-12|Blog|Comments Off on How do you calculate the weight of mineral wool panels for delivery and installation?

Load-bearing and cladding profiles: how trapezoidal sheets differ

Structural and cladding trapezoidal sheets serve different functions, even though both have longitudinal ribs. The cladding type forms a covering or enclosure, while the structural type is selected for a specific load-bearing role. Before comparing prices, establish what task the product must perform. Check the cross-section drawing, the effective cover width and the load documentation. A higher profile does not always mean greater load capacity, because steel thickness and grade also matter. The same T18 or T35 symbol does not guarantee identical parameters across different offers. Note the support arrangement and which side of the sheet is intended for exposure.

By |2026-11-15T00:58:15+01:002022-09-05|Blog|Comments Off on Load-bearing and cladding profiles: how trapezoidal sheets differ

What to consider when building a fully hipped roof

A hipped roof has four slopes and diagonal corners that tidy the building's form but alter the loft space and the number of cuts and details. Before choosing a design, check the actual roof plan with sections and building dimensions, not just the name of the form. Assess the proportions between slope height, elevation and eaves overhang, as well as the heights above planned passages and furniture. For trapezoidal sheet or metal tile covering, ask for a layout plan of sheets or modules, because diagonal corners require cuts limited by laps and profile geometry.

By |2026-11-15T00:57:10+01:002022-08-30|Blog|Comments Off on What to consider when building a fully hipped roof

What load-bearing trapezoidal sheets do and how to compare costs

In Poland, structural trapezoidal sheet carries loads and provides a base for subsequent roof layers, but its selection requires checking the geometry, steel grade and thickness, and support spacing. Manufacturer tables refer to a specific arrangement, so load capacity cannot be transferred between profiles. It is also worth establishing whether the sheet's own weight is included and what the support conditions are. Assess cost on the same square-metre basis, bearing in mind the difference between material development and covered area.

By |2026-11-14T17:31:53+01:002022-08-14|Blog|Comments Off on What load-bearing trapezoidal sheets do and how to compare costs

Choosing a façade colour when the roof colour is already fixed

If the roof is already in place, use its colour as the starting point for the façade. Compare samples of the roofing, render and window frames outdoors at the same time. Tilt the roofing sample to match the pitch and see how the combination looks against nearby buildings. Check local planning requirements before settling on the palette. For a façade made from sandwich panels, consult the system documentation as well: the chosen colour can affect the permitted support spacing.

By |2026-11-15T04:49:31+01:002022-07-25|Blog|Comments Off on Choosing a façade colour when the roof colour is already fixed

Would a sheet metal or metal picket fence suit your property?

First work out which parts of the plot genuinely need screening. Solid trapezoidal sheet panels and see-through metal slats do different jobs, so before deciding, assess wind exposure, how much privacy you want, the shape of the ground and the style of the house. Full infill is handy beside a terrace or a busy street, while at a driveway good visibility matters most. You need not repeat one pattern across the entire property – some sections can have smaller openings, others an open view of planting and the entrance.

By |2026-11-14T21:03:09+01:002022-07-18|Blog|Comments Off on Would a sheet metal or metal picket fence suit your property?

Which standing seam should you choose before ordering the substrate and the crew?

Traditional standing seam and snap-lock panels require different installation methods. It is not worth choosing them only after the substrate has been installed. The differences concern how the joint is formed, the fixing and the thermal movement of the steel sheet. The minimum pitch also depends on the specific solution. Below we explain what to agree before starting the roof. In traditional covering, the edges are appropriately shaped and closed by the installer. A single standing seam has a different formation from a double standing seam, which requires an additional fold of the joint. A snap-lock panel, however, has factory-prepared edges. These are joined according to the system instructions, without treating them as a traditional standing seam to be bent at will.

By |2026-11-14T11:10:38+01:002022-07-15|Blog|Comments Off on Which standing seam should you choose before ordering the substrate and the crew?

How to plan a quieter interior with insulated wall panels?

Choosing a panel with mineral wool does not automatically guarantee a quiet hall. Noise passing through the wall must be separated from reverberation inside. Doors, openings and connections are of great importance. An acoustic plan is best prepared before ordering the enclosure, when the layout of rooms and installations can still be changed. First establish where the sound source is and who is to be protected. An office next to a workshop requires a different solution from a warehouse next to a busy road. The type of noise, frequencies and operating times of equipment matter. The wall area alone does not indicate what result will be required.

By |2026-11-14T11:12:45+01:002022-07-15|Blog|Comments Off on How to plan a quieter interior with insulated wall panels?
Back to top