About PiVi

This author has not yet filled in any details.
So far PiVi has created 1404 blog entries.

How many sandwich panel screws do you need for the actual fixing layout?

The number of screws results from the panel layout, supports and loads. The same square metreage may require a different number of fastenings at the edge of the building than in its central part. A rate per metre is only useful once the whole layout has been calculated. It should not replace drawing out the locations where the fasteners are to work. Gather the panel laying plan and the support layout. The panel lengths, cladding thickness and type of structure are needed. Also check the method of fixing: visible or intended as concealed in the joint. Not every system uses the same detail.

By |2026-11-14T14:21:57+01:002025-02-08|Blog|Comments Off on How many sandwich panel screws do you need for the actual fixing layout?

How do you choose panel lengths for delivery and installation?

The longest available panel is not always the best choice. It has to be delivered, lifted and supported on suitable supports. Shorter sections can make logistics easier but create additional joints. The length should therefore be determined together with the cladding design and installation plan before the final order is placed. The production range indicates which elements can be made within a given family. It is not, however, a table of permissible spans. A long panel may still require several supports. Their spacing depends on the loads and the parameters of the specific variant.

By |2026-11-14T14:21:46+01:002025-01-20|Blog|Comments Off on How do you choose panel lengths for delivery and installation?

What should a hands-on roofing course teach?

In Poland, good roofing training should teach work with a specific system, reading documentation and solving difficult details, not just a demonstration of quick panel installation. Participants should check how much time they spend at a workstation and whether the instructor also discusses mistakes. Such knowledge helps to install a watertight roof and communicate more efficiently with the investor. Before choosing a course, define what you want to learn: a beginner needs the basics of work organisation, measurement and safety, while an experienced crew may seek knowledge about a new profile or difficult flashings.

By |2026-11-14T17:31:11+01:002025-01-18|Blog|Comments Off on What should a hands-on roofing course teach?

Roof panel thickness: which design checks come first?

The best way to choose the roof thickness is to start with the conditions inside the building and the project requirements. Only then do you check the panel's load-bearing capacity, the supports and the details. Reversing this order can prove costly. A panel bought simply because it was available may force structural changes or fail to deliver the assumed thermal insulation for the whole assembly. Establish the temperature, humidity and duration of use of the rooms. An unheated warehouse, a cold store and a workshop in daily use each place different demands. Also describe the planned changes. If the building is to be heated in two years, it is worth taking this into account before choosing the panel.

By |2026-11-14T17:29:19+01:002025-01-06|Blog|Comments Off on Roof panel thickness: which design checks come first?

How chimney flashing meets a metal roof

Flashing around a chimney on a metal roof must take over the water flowing down the slope and direct it safely onto the covering, while allowing for roof movement and the chimney construction. Simply applying tape or sealant is not enough. Check the geometry of the detail, the order of laps, the fit to the sheet profile and the connection to the chimney. Pay attention to drainage behind the chimney, fixings in the water-flow zone and the termination of the flashing at the vertical part of the chimney.

By |2026-11-15T00:56:50+01:002025-01-02|Blog|Comments Off on How chimney flashing meets a metal roof

Why is a photovoltaic roof not generating power in sunshine?

Sunny weather and a zero reading in the app do not point to one specific cause. The problem may lie in data transmission, the inverter, the grid or part of the installation. Sometimes the system is working, but the reading has not yet been refreshed. The first step is to establish what is actually not working. Safe observation and a good description of the symptoms are more useful than randomly resetting devices. Check the time of the last update and the messages available to the user. If the app shows data from several hours ago, communication may be the cause. It is worth comparing it with the information on the device or another data source provided in the instructions. Do not open the enclosure or touch connections to confirm a suspicion.

By |2026-11-15T20:22:16+01:002024-12-29|Blog|Comments Off on Why is a photovoltaic roof not generating power in sunshine?

What are the advantages and limitations of mineral wool panels when building in stages?

Mineral wool panels combine the enclosure and insulation in a single element. They can facilitate rapid closing of the building and meeting specific fire requirements. However, account must be taken of weight, support and careful sealing of joints. When building in stages, exposed ends and consistency between successive batches must also be ensured. The panel consists of two facings and a core bonded to them. Installing the complete element can reduce the number of separate enclosure operations. Not every layer has to be installed as in a wall assembled on site. This helps to organise the schedule, especially when the priority is to close the building before further works.

By |2026-11-14T11:11:24+01:002024-12-15|Blog|Comments Off on What are the advantages and limitations of mineral wool panels when building in stages?

When should you order T14 trapezoidal steel sheet and how should you prepare the structure for it?

It is worth choosing the T14 sheet before building the frame. The profile height alone does not indicate the correct support spacing. First, the application, steel thickness and loads must be determined. Only then can the sheets be ordered. Below we show how to carry out this stage without costly changes on site. The designation T14 refers to a family of low trapezoidal profiles. It is not a full product description. Under this name there may be sheets with different cover widths, thicknesses and profile arrangements. Therefore, an order limited to “T14 in graphite colour” leaves too many unknowns.

By |2026-11-14T11:09:32+01:002024-12-08|Blog|Comments Off on When should you order T14 trapezoidal steel sheet and how should you prepare the structure for it?

What does the price per square metre of trapezoidal steel sheet actually cover?

The amount next to the profile symbol is only the beginning of the comparison. You need to establish what area it is calculated for and which variant it describes. Sheets with the same trapezoid height may have a different steel thickness or coating. Only after aligning these data can you assess the price per metre of material needed for the roof. Check whether the amount refers to a gross square metre, an effective square metre or a linear metre. Each of these units can lead to a different figure for the same sheet. A price without a specified unit does not allow a reliable comparison of two items.

By |2026-11-14T14:21:44+01:002024-12-08|Blog|Comments Off on What does the price per square metre of trapezoidal steel sheet actually cover?

Choosing panel thickness for thermal performance and moisture control

Panel thickness must be linked to the building requirements, the product properties and the conditions within the building envelope. The U-value table does not cover all of these matters. Likewise, a standard designation is not permission for arbitrary installation. It is best to go through the selection in several steps and finalise the details before panel production. Determine the building's use and the room temperatures. Check the formal basis applicable to the project. The older WT 2021 reference appears in many materials but should not replace such a determination. The requirements must be checked for the specific project and the basis of its design.

By |2026-11-14T14:20:22+01:002024-12-01|Blog|Comments Off on Choosing panel thickness for thermal performance and moisture control
Back to top