+48 500 409 109

What is tile-effect metal roofing made of and how does it fit into the whole roof?

Tile-effect metal roofing is a profiled metal sheet with protective layers. The pressings give it its shape and rigidity. The sheet itself is only the covering. Insulation, airtightness from the inside and ventilation belong to the whole roof assembly. It is worth understanding this division before ordering material and dividing work between teams. In common steel solutions, the base is a thin steel core. It is protected by a metallic layer and an appropriate coating system. The external organic coating gives the colour and influences the surface resistance. The underside also has protection. The exact construction depends on the product and should be described in its documents.

By |2026-11-14T11:10:57+01:002022-07-10|Blog|Comments Off on What is tile-effect metal roofing made of and how does it fit into the whole roof?
Read More

Which roof covering works for a holiday cabin?

The choice of roofing for a holiday cottage depends above all on how the building will be used. Before buying sheet metal, establish whether the cottage will be heated only occasionally or also in winter. With weekend heating, a rapid temperature rise increases the amount of moisture reaching cold surfaces, so check the layer build-up, insulation and ventilation. Metal roof tiles or T18 and T35 trapezoidal profiles may suit a simple form, but match the pitch, batten spacing and eaves detail to the specific model. Unloading, transport and access for cleaning also influence the choice.

By |2026-11-14T21:02:27+01:002022-06-13|Blog|Comments Off on Which roof covering works for a holiday cabin?
Read More

Refurbishing metal fence pickets: when cleaning is no longer enough

An older fence may need refreshing, but not every deterioration in appearance means it has to be painted. Some changes are caused by dirt, others affect the coating itself. Metal fence pickets must first be assessed and identified. Only then can the scope of work be chosen. Renovation with an unsuitable paint can make the appearance worse, complicate later repairs and leave the problem under a new layer. Inspect the front, the back, the ends and the fixing points. Mark the sections that are dirty, scratched, and those with coating detachment or corrosion. Different parts may be in a different condition. There is no need to assume in advance that they all need identical treatment. Photos will help you compare the effect of cleaning and further work.

By |2026-11-15T20:21:54+01:002022-06-05|Blog|Comments Off on Refurbishing metal fence pickets: when cleaning is no longer enough
Read More

Measuring a roof valley: where the two roof slopes meet

The valley gutter works at the point where water from two parts of the roof arrives. Measuring its length is only the beginning of the preparation. You need to identify the layout of the slopes, the line of their intersection and how the covering is finished. The area from which the water flows also matters. Not every pair of slopes forms the same angle and the same detail. A well-described valley allows the flashing to be selected without accidentally narrowing the channel during installation. On the plan, mark both slopes and the line of their intersection. Add the flow directions and any obstacles that may change the path of the water. A dormer, chimney or roof break affects the local layout. The length of the valley alone does not show how much of the slopes the flashing has to serve.

By |2026-11-15T04:43:53+01:002022-06-05|Blog|Comments Off on Measuring a roof valley: where the two roof slopes meet
Read More

How the protective layers on a steel roofing sheet work together

The properties of steel sheet depend on the whole layer system, not on colour alone. Before measuring, ordering or accepting delivery, check whether the steel core and metallic coating are described separately from the organic layer, because each performs a different function. Pay attention to the environmental intended use, protection on both sides of the sheet, and the compatibility of fixings and processing. The appearance of a sample alone is not enough to assess durability, while the manufacturer's declarations allow products to be compared on a common basis.

By |2026-11-15T04:42:52+01:002022-05-25|Blog|Comments Off on How the protective layers on a steel roofing sheet work together
Read More

Repairing a leaking sheet metal roof

Start by tracing how water gets into the roof. A ceiling stain is not always directly beneath the leak. Laps in the sheet, flashings, fixing points or condensation under the covering may be to blame. Only diagnosis lets you decide whether to replace an element, improve a detail or use a suitable sealant. Note when dampness appears. Wind-driven rain, thawing snow and a cold morning point to different causes. Inspect the visible part of the loft and the membrane's layout. Water can run along the structure and emerge far from its entry point.

By |2026-11-14T21:02:01+01:002022-05-08|Blog|Comments Off on Repairing a leaking sheet metal roof
Read More

Choosing battens and batten spacing for trapezoidal steel roofing

Selecting purlins and their spacing for trapezoidal sheet begins with the specific profile's data sheet, not the product name alone. Check the profile, steel thickness and grade, loads and the sheet's support scheme. T18 and T35 do not share one common purlin spacing. Load capacity depends on cross-section geometry, not just profile height. Purlins spacing sets the sheet spans, while rafter spacing affects the purlins themselves – these are two separate checks. The design should define the geometry of the whole system.

By |2026-11-15T00:56:52+01:002022-04-26|Blog|Comments Off on Choosing battens and batten spacing for trapezoidal steel roofing
Read More

Ordering parapet coping: measuring width, fall and corner details

The parapet flashing must cover the top of the wall and drain water in the intended manner. Its width follows from the finished wall cross-section including all layers. The order also requires the leg heights, the direction of fall and the geometry of the corners. A part that fits on a straight run may not resolve the termination at a higher wall. It is therefore worth preparing the measurement as a set of related details. Include the masonry, insulation and finishing layers on both sides. If measuring in advance, the intended thicknesses must be entered on the drawing. The dimension of the base or raw parapet alone is not sufficient. A cap that is too narrow may not ensure the correct position of the side edges.

By |2026-11-15T04:43:54+01:002022-04-03|Blog|Comments Off on Ordering parapet coping: measuring width, fall and corner details
Read More

Installing trapezoidal sheets on a roof: alignment, laps and fixings

Whether a trapezoidal metal roof will be watertight depends on installation matching the documentation for the chosen profile and the structural design, not on the T18 or T35 label alone. Before measuring, ordering or accepting delivery, it is worth confirming the roof pitch, sheet lengths, support layout and loads, as well as the steel thickness and coating variant. These parameters can matter more than a generic recommendation because they determine how the sheets are laid and fixed. Below we set out the key stages and the points to check with the contractor.

By |2026-11-15T04:41:56+01:002022-03-29|Blog|Comments Off on Installing trapezoidal sheets on a roof: alignment, laps and fixings
Read More

Modular tile-effect sheets: suitable roofs and installation planning

Modular metal roofing can work on a simple house as well as on a roof with numerous bends, provided the measurement and substrate preparation are accurate. Above all, the investor should check the actual cut layout of the slope and whether the chosen pattern matches the system, since dimensions and the number of ribs vary between manufacturers. It is also worth agreeing the batten spacing resulting from the specific module with the roofer and planning roof penetrations in advance. The decision to choose modules should rest on roof geometry, transport logistics and the expected appearance, leaving technical details to the designer.

By |2026-11-14T21:00:54+01:002022-03-19|Blog|Comments Off on Modular tile-effect sheets: suitable roofs and installation planning
Read More
Back to top