About PiVi

This author has not yet filled in any details.
So far PiVi has created 1404 blog entries.

When and how to clean an integrated photovoltaic roof

Cleaning makes sense when it responds to a real need and is carried out in accordance with the covering's instructions. Not every deposit requires immediate washing, and rain does not remove all soiling. On an integrated roof, the active surface, the steel coating and the connections must all be protected at the same time. It is worth first assessing the condition of the roof and the access conditions. Only then should the method and timing of the work be chosen. Visible local soiling, accumulated leaves or deposits hindering water drainage may require action. A prolonged drop in production is a signal to check the cause, but does not in itself prove dirt. Weather conditions and device messages should be taken into account.

By |2026-11-15T20:22:28+01:002024-07-04|Blog|Comments Off on When and how to clean an integrated photovoltaic roof

The autumn roof check: what to look for before temperatures drop

An autumn roof inspection is best planned before the first frost makes its condition harder to assess. Begin by viewing the building from the ground and from safely accessible places, and only then commission a more detailed check by a contractor. The key decision is which signals — shifted flashings, damaged gutters or marks on the façade — call for immediate action and which can simply be noted for the next inspection. Photographs from the previous check make it easier to point out changed areas. On that basis, set the scope of work and the order of repairs before winter.

By |2026-11-15T04:42:10+01:002024-06-24|Blog|Comments Off on The autumn roof check: what to look for before temperatures drop

Sheet metal roofing complaints: tracing damage to its cause

Most complaints about sheet-metal roofing rarely stem from a single cause – they may originate in the material, transport, storage, installation or later use of the roof. Before reporting a problem, it is therefore worth establishing whether it concerns a specific detail or the entire slope, and gathering documents and installation photos. The key variable is the location of the mark and the roof's history: a rusty spot is assessed differently from a discolouration, and differently again from an unevenness. A close-up alone is often insufficient, so a general view and the date the symptom was noticed are needed.

By |2026-11-15T04:42:54+01:002024-06-24|Blog|Comments Off on Sheet metal roofing complaints: tracing damage to its cause

Where do insulated wall panels with a mineral wool core help meet building requirements?

Insulated wall panels with a mineral wool core are used where cladding with specific thermal, fire or acoustic properties is required. They may appear in industrial halls and public buildings. However, the suitability is not determined by the name of the core alone. The entire wall assembly, including openings and connections, is important. One of the reasons is the requirements relating to the behaviour of the wall during a fire. Panels with a mineral core can have appropriate reaction-to-fire classes and fire resistance classifications. However, the specific product and the method of installation must be checked. Not every thickness and span gives the same result.

By |2026-11-14T11:11:14+01:002024-06-21|Blog|Comments Off on Where do insulated wall panels with a mineral wool core help meet building requirements?

Buying a 13.5 m roof panel in RAL 3009: what should you check on a 40 mm panel?

A 13.5 m roof panel can reduce the number of joints on the roof slope. However, this dimension requires planned transport, lifting and supports. With a thickness of 40 mm, the insulation performance must be assessed separately. If the material is second grade, a precise inspection of the condition of each piece is also required before purchase. The 40 mm thickness refers to the nominal dimension specified for the given panel. In a roof panel with trapezoidal sheeting, the height at the rib is greater than in the profile valley. RAL 3009 describes an oxide red shade, but not the type of coating or its resistance in the environment.

By |2026-11-14T14:20:37+01:002024-06-17|Blog|Comments Off on Buying a 13.5 m roof panel in RAL 3009: what should you check on a 40 mm panel?

Why does the north wall get damp and what should be checked before insulating it?

A damp north wall does not always mean a lack of insulation. The cause may be a leak, moisture from the ground or an internal surface that is too cold. A north-facing elevation usually receives less sun, so it dries more slowly. A good renovation starts with identifying the path of the water, not with buying the thickest board. Note whether the patch grows after rain, after several cold nights or regardless of the weather. Inspect the wall on both sides. A stain at ceiling level may be linked to the roof or flashings. Moisture in the lower section requires checking the plinth, the ground and the insulation at ground level. The shape of the patch alone does not yet give a reliable diagnosis.

By |2026-11-14T11:12:18+01:002024-06-12|Blog|Comments Off on Why does the north wall get damp and what should be checked before insulating it?

Vapour control layers and roof underlays: choosing by position and purpose

The key to choosing roof membranes correctly is to establish what each layer does in the specific build-up, not to rely on the product name alone. Before measuring, ordering or accepting delivery, check the roof section: where the vapour control layer should sit on the inside, where the membrane under the covering belongs, and how ventilation has been designed. The use of the rooms and the type of insulation, including PIR, also matter. Only then should you select materials and the accessories for laps and seals.

By |2026-11-15T04:41:58+01:002024-06-09|Blog|Comments Off on Vapour control layers and roof underlays: choosing by position and purpose

How do you choose sandwich panels and budget for cladding before extending a building?

An extension begins with the decision on how the larger building should function. Only then are the panels selected and their cost calculated. The new part should match the structure, internal conditions and construction programme. It is worth following this sequence before the first material quote appears. Determine what will change once the work is complete. Will the new part be heated, how often will the gates open and what processes will take place inside? Extending a warehouse with a workshop may mean different requirements than adding another dry storage space.

By |2026-11-14T14:21:15+01:002024-06-07|Blog|Comments Off on How do you choose sandwich panels and budget for cladding before extending a building?

From measuring a roof to specifying its trapezoidal steel sheets

Choosing trapezoidal steel sheet starts with the roof, not with the colour in the sample book. You need to know its geometry, its supports and the conditions of use. Only then can you select the profile, the steel and the coating. The cutting plan and the complete order come at the end. This sequence reduces the risk of buying sheets that require costly reworking. Record the eaves length, the length of the run down the slope, the pitch and the position of all openings. Check the diagonals and the dimensional differences between the edges. When renovating, do not assume that the old roof has exactly the shape shown on the old drawing.

By |2026-11-14T17:29:59+01:002024-06-01|Blog|Comments Off on From measuring a roof to specifying its trapezoidal steel sheets

The benefits and limitations of multi-pitched roofs

In Poland, a multi-pitched roof is often chosen for a complex building form, but its advantages and limitations must be weighed together. Such a layout has more edges, valleys and junctions than a simple roof, which affects cost, cutting and insulation work. Before deciding, check whether the roof geometry matches the building footprint, how drainage is resolved and whether the details at corner junctions maintain insulation continuity. Also compare covering options on the same footprint, taking into account the number of elements and expected offcuts.

By |2026-11-14T17:32:25+01:002024-05-30|Blog|Comments Off on The benefits and limitations of multi-pitched roofs
Back to top