About PiVi

This author has not yet filled in any details.
So far PiVi has created 1404 blog entries.

How should you prepare wall calculations so that a quick result is suitable for the project?

The calculator can work out wall layers in a few moments. Most of the work, however, goes into establishing what is actually inside the building element. Before renovation, you need to separate the verified condition from assumptions. Only then is it worth comparing PIR thicknesses, assessing the risk of moisture and preparing data for the contractor. Start with the wall cross-section. Record the order of materials from the interior to the surroundings. Include renders, masonry, the cavity and any existing insulation. For each layer, give the thickness and how it was determined. A measurement in an opening gives a different level of certainty from the owner's memory of a renovation twenty years ago.

By |2026-11-14T11:12:04+01:002025-09-06|Blog|Comments Off on How should you prepare wall calculations so that a quick result is suitable for the project?

How timber members are joined in a roof frame

What decides how timber roof beams are joined is chiefly the direction of the forces, where the supports sit and whether the detail can actually be built. Before choosing a connector, work out which loads pass between the beams, whether the joint is compressed, tensioned or acts in several directions, and whether it falls over a support or within a span. Two similar-looking details may behave quite differently. Check the cross-sections, grade and condition of the timber, the surrounding conditions, and real access to the fixings for inspection.

By |2026-11-15T00:56:38+01:002025-09-01|Blog|Comments Off on How timber members are joined in a roof frame

Choosing a roofing contractor and agreeing exactly what the price covers

First establish who is responsible for measuring and checking the material schedule before ordering, as this determines later responsibility for matching the covering. It is also worth checking the crew's experience with the chosen material and with a similar roof geometry, not only with a simple shelter. Before deciding, ask for documentation from several stages of the work and inquire how details will be resolved. Only then compare offers on the basis of the same scope, acceptance conditions and rules for settling additional work.

By |2026-11-15T04:42:13+01:002025-08-27|Blog|Comments Off on Choosing a roofing contractor and agreeing exactly what the price covers

Where can T8 be used when finishing or extending a building?

T8 has a low profile, so it is often considered for lightweight cladding and finishes. When extending, it is important that the new sheet matches the existing surface. The T8 designation alone does not guarantee this. The cross-section, cover width and coating must be compared. Use on a roof requires separate confirmation. No. Low profiles can also be used in cladding and on façades if the documentation for the specific product provides for it. Soffit is one of the possible areas. In every case, support, fixings and wind exposure conditions matter. A small corrugation height does not exempt you from these checks.

By |2026-11-14T11:10:52+01:002025-08-22|Blog|Comments Off on Where can T8 be used when finishing or extending a building?

Fitting a rainwater gully at the foot of a downpipe

A silt trap beneath the downpipe catches leaves, twigs and sediment before rainwater reaches the underground pipe. Its removable basket lets you empty it and check the outlet without dismantling the installation. Before fitting, establish whether the outlet is at the bottom or the side, and match the unit to the pipe diameters and ground loading. Ensure easy access to the basket and firm seating of the body – these are the conditions for correct operation.

By |2026-11-15T00:57:45+01:002025-08-06|Blog|Comments Off on Fitting a rainwater gully at the foot of a downpipe

Lifting fibre cement sheets onto a roof without damage

Lifting the roofing onto the roof should be planned before installation begins. Fibre cement sheets are fragile under impact and do not tolerate accidental bending. Asbestos-free fibre cement requires the correct method of gripping, transporting and setting down. How this work is organised affects both the safety of the people and the condition of the sheets. Two sheets of similar material can differ considerably in size. Before choosing a lifting method, you need to know their actual weights and lengths. Do not rely on the general assumption that fibre cement is light. The place where the sheet is to be handed over to the team at height is also important. A large format reduces the number of joints on the roof slope but increases the transport requirements.

By |2026-11-15T20:23:07+01:002025-07-27|Blog|Comments Off on Lifting fibre cement sheets onto a roof without damage

Choosing battery storage for an existing photovoltaic roof

An existing photovoltaic roof can be considered as an energy source for a battery storage system, but selecting the battery requires checking the entire installation. First, the objective must be established and the energy flows identified. Then the compatibility of the devices, the capacity, the power and the installation location are assessed. Comparing the number of kilowatt-hours with the roof output alone is too simplistic. What matters is when the surplus arises and when it will actually be needed. The most common objective is to shift part of the energy from the production hours to later consumption. Another may be a reserve in the event of a grid failure. These tasks are not identical. A battery used intensively every evening may have little reserve at the moment of a sudden interruption.

By |2026-11-15T20:22:33+01:002025-07-19|Blog|Comments Off on Choosing battery storage for an existing photovoltaic roof

Scheduling a house build and deciding when to order the roof

In Poland, the time needed to build a house depends on the technology, organisation, weather and delivery schedules, so no single number of months can be reliably promised for every project. Readers should check what conditions each stage must meet — from documentation through groundworks and structure to the roof, installations and finishing — and which tasks can run in parallel. The roof, while it protects subsequent work, requires earlier arrangements. A schedule should show the dependencies between stages, not just dates written next to team names.

By |2026-11-14T17:31:15+01:002025-07-12|Blog|Comments Off on Scheduling a house build and deciding when to order the roof

Roof battens and how they work with the covering

In Poland, roof battens provide direct support for the covering and transfer its loads to the rafters or purlins. Before laying the first sheet, it is worth checking that their cross-section, spacing and fixing match the specific metal profile and the roof structure. The key variable is matching the solution to the manufacturer's requirements and the design, rather than repeating a habitual pattern. The geometry of the slope, the eaves line and critical zones such as the ridge or valleys should also be verified.

By |2026-11-14T17:30:51+01:002025-07-08|Blog|Comments Off on Roof battens and how they work with the covering

Building a roof without an overhang: benefits and practical limits

A roof without eaves is a deliberate design decision, not merely the omission of a projecting overhang. It gives a compact form and a clear line where roof meets wall, but requires careful detailing of drainage, ventilation and edge insulation. No eaves does not automatically mean a gutter hidden in the facade. The edge section should be drawn, because wall insulation thickness, gutter position and edge height all affect one another. Check that these are resolved coherently and that service access to the gutter is provided.

By |2026-11-15T00:56:29+01:002025-07-02|Blog|Comments Off on Building a roof without an overhang: benefits and practical limits
Back to top