Blog2026-11-15T20:04:30+01:00

Choose a product group

Metal roofing

Blachy trapezowe — ilustracja kategorii

Sandwich panels

Płyty warstwowe — ilustracja kategorii

PIR insulation boards

Płyty izolacyjne PIR — ilustracja kategorii

XPS

Płyty XPS — ilustracja kategorii

Accessories

Wkręty i łączniki — ilustracja kategorii

Fencing

Sztachety metalowe — ilustracja kategorii

Blog

The Izoprofil.net blog answers practical questions about renovation, extensions and the sequence of work. Find out where to start looking for a leak, when to order roofing sheets, how to prepare a delivery area and what to establish before installing insulation. The articles cover measurements, the condition of existing components and order details for roofing, sandwich panels and PIR insulation. They explain which information to collect and when an on-site assessment by a professional is needed. Choose the article that matches the current task so you can prepare a more accurate materials enquiry and reduce rework.

Protecting the lower ends of metal fence pickets beside a lawn

The lowest part of the fence is often the most exposed to everyday dirt. Water from the ground, cut grass and material carried during garden work end up there. The lower ends are also easily buried when adding soil. Pickets made of sheet metal need the same attention in this zone as the attractive front. A well-planned surroundings make later maintenance of the fence easier. The clearance under the pickets should match the intended layout and the needs of the property. There is no single figure that is right for all fences. The terrain, surface, use and product documentation must be taken into account. It is worth checking whether, after the lawn or driveway has been created, the actual level has not changed relative to the plan.

When should you choose PIR 120 × 60 cm and when the larger 120 × 240 cm boards?

A large PIR board can speed up covering an open area. The smaller format is easier to carry into a tight room and to fit around many openings. The whole course of the works should determine the choice. It is worth calculating the cutting layout and checking the transport route before the material is ordered by the square metre. Among the available insulation boards, sizes of 600 × 1200 mm and 1200 × 2400 mm are found. Their geometric area is 0.72 and 2.88 m² respectively. The large format therefore has four times the area. This does not mean, however, that every PIR variant is offered in both dimensions.

When is the extra cost of a mansard roof worthwhile?

A mansard roof is worth considering when the extra attic space is genuinely needed, not when the simplest and cheapest construction is the only priority. Before deciding, check how much room the chosen geometry provides after insulation is installed, how the slope break, flashings and insulation continuity are resolved, and whether the gentler upper section meets the requirements of the selected covering. It is also worth assessing the extent of details around dormers and valleys and comparing quotes that cover the same scope of work.

PIR or XPS for a flat roof: what determines the choice during renovation?

On a flat roof, the layer build-up is chosen first, and only then the specific insulation. PIR under the waterproofing and XPS in an inverted roof perform under different conditions. Comparing price or lambda alone overlooks this difference. During renovation, the condition of the old roof, the height of the outlets and the feasibility of the details are equally important. In a traditional roof build-up, the thermal insulation sits beneath the water-protecting layer. Suitable PIR boards are used in such systems with a membrane or roofing felt. The facing, the method of fixing and the remaining layers must be matched to the overall solution.

What work is T12 suitable for and what should be checked before installation?

T12 is a low profile that should be assessed in relation to the specific task. It may be considered for light cladding and finishes. Suitability for a roof is determined by the documentation for the selected variant. Before purchase, the cross-section, thickness and support must be checked. The designation alone does not describe the entire sheet. The number in the designation indicates the profile family but does not replace a technical drawing. Two sheets of similar height may differ in the arrangement of the ribs and in width. They may also have a different lap position. This is particularly important when a new section is to connect to existing cladding.

Why consider a metal covering for your roof?

In Poland, metal roof covering is worth considering primarily because of its low weight, wide choice of profiles and adaptability to different buildings. It is not, however, a single product with fixed parameters: T18, T35, metal roof tiles and sandwich panels serve different functions. Before choosing, check which layers make up the complete roof assembly, whether the structure can carry loads from snow, wind and planned equipment, and what minimum pitch applies to the specific product. The weight of the sheet alone does not describe the assembly or confirm the good condition of an old roof truss.

Back to top